Search found 59 matches
- Mon Feb 06, 2017 3:34 am
- Forum: Racks, Switching Systems and MIDI
- Topic: Selectable buffer on GCX?
- Replies: 6
- Views: 7823
Re: Selectable buffer on GCX?
That's what I was looking for. Thanks John.
- Sat Jan 28, 2017 1:39 pm
- Forum: Racks, Switching Systems and MIDI
- Topic: Selectable buffer on GCX?
- Replies: 6
- Views: 7823
Re: Selectable buffer on GCX?
Both of those would work. Related question: the normaling of the jacks, they're switched at the front? That is, the rear jacks are in parallel until something gets plugged it the front "feed though"? I'd like to feed the buffer from the rear...output of loop 1 (fuzz) to the rear feedthrough, jumper ...
- Thu Jan 26, 2017 7:58 pm
- Forum: Racks, Switching Systems and MIDI
- Topic: Selectable buffer on GCX?
- Replies: 6
- Views: 7823
Selectable buffer on GCX?
Is there a way to patch the buffer into loop 1 so I can take it out of circuit when I use my fuzz?
- Sat Jan 30, 2016 7:05 pm
- Forum: Racks, Switching Systems and MIDI
- Topic: Control Switcher with GCX loops ?
- Replies: 5
- Views: 6355
Re: Control Switcher with GCX loops ?
It sounds like you have an abundance of things to control, you just need a better way to control them. There are a lot of things to consider in upgrading your controller. A small foot print is nice, but the flexibility to get what you need done is very important. (And you don't need to necessarily c...
- Sat Jan 30, 2016 6:42 pm
- Forum: Racks, Switching Systems and MIDI
- Topic: second Midi pedal for IAs
- Replies: 5
- Views: 6277
Re: second Midi pedal for IAs
I think you can run the MIDI mate into the GCP and pass the CC messages on to other devices. You didn't say what else you were controlling. If you're controlling a GCX, I'd not sure what will happen if it can get the SYS Ex messages from the GCP and the CC messages from the MIDI mate. What are you c...
- Sat Jan 30, 2016 6:27 pm
- Forum: Racks, Switching Systems and MIDI
- Topic: GCX not powering the GCP
- Replies: 6
- Views: 7132
Re: GCX not powering the GCP
Be sure that the cables have all five pins connected. Also (especially if you aquired the GCP used) be sure that the DIN Jack on the GCP is clean. (Power it down and give it a blast of contact cleaner.)
- Sat Jan 30, 2016 6:14 pm
- Forum: Racks, Switching Systems and MIDI
- Topic: GCX engaging presets on multiple devices (one stomp)
- Replies: 5
- Views: 5750
Re: GCX engaging presets on multiple devices (one stomp)
If you want to conservce loops in the GCX (and simplify the wiring) you can wire the Strymon between the Output of the GCX and the input of the amp, or directly in the effects loop of the amp and program a preset in the Strymon with all dry signal. When you send the PC message and change to the "dry...
- Fri Jan 29, 2016 3:11 pm
- Forum: Racks, Switching Systems and MIDI
- Topic: Multiple Amp Switching GCX
- Replies: 4
- Views: 5903
Re: Multiple Amp Switching GCX
Hello, and welcome!! What you want to do is dead simple, and the best part is you can do it with a single GCX Loop. Check out Example 2 on Page 8 of the GCX Manual. This is the easiest way to make your front end connections, and all you'll need to do is split the signals coming out of Send and Out ...
- Fri Jan 29, 2016 11:04 am
- Forum: Racks, Switching Systems and MIDI
- Topic: Multiple Amp Switching GCX
- Replies: 4
- Views: 5903
Re: Multiple Amp Switching GCX
Simple enough. Are you running the amp pairs in stereo or mono?
- Tue Jan 26, 2016 8:50 pm
- Forum: Racks, Switching Systems and MIDI
- Topic: second Midi pedal for IAs
- Replies: 5
- Views: 6277
Re: second Midi pedal for IAs
I'll be curious to hear if you can make it work. You won't be able to send the CC messages from the ia's withe the presets. You would probably be better off with a single more sophisticated controller.