Wiring a pedal board and using an ISO 5 and a PP2+

[firebird1999us]

So here's what I need to power:

Custom Audio Wah
Digitech Whammy V
Boss TU2 (I'm daisy chaining an MXR Loop box, a Loopmaster true bypass, a channel switch, and an A/B/Y box off of the TU2 for LED power only)
MXR Phase 90
Boss TR2
MXR Chorus
Ibanez Paul Gilbert Airplane Flanger
Xotic SP Compressor (don't have it yet - it's the blank spot next to the fatboost in the pic)
Fulltone Fatboost 3
Fulltone Fulldrive II @ 18v
Boss EQ20 (where the DD20 is placed for sizing)
TC Electronics Ditto Looper X2
Vox Delaylab

I'm trying to figure out the logistics of this and if the PP2+ and the ISO5 is enough?

This is the layout of the board... the cardboard spots represent the 3 loopmaster pedals on the way. I'm also adding large pedal props to either side so everything is off the ground and connected...

[JohnClark]

Exactly which model is the MXR Chorus you have? That is the only one here I am unsure of. Do you know if it requires 9V or 18V?
If you want to run the Fulldrive 2 at 18V then you can power it from the 18V Output on the ISO-5. But if the Chorus needs the 18V output, you can run the Fulldrive 2 at 12V using any one of outputs 1-4 with the corresponding DIP switch set away from Normal.

The DelayLab, EQ-20, and Whammy 5 are your high current pedals. Each one can be powered from outputs 5 or 6 on a Pedal Power 2+ with the DIP switches set to Normal, or from the High Current 9V output on the ISO-5.

All the rest of the pedals can be powered from any of the remaining outputs on the Pedal Power 2+ with the corresponding DIP switches set to Normal, and the three 9V Outputs on the ISO-5.

I hope that helps!

[firebird1999us]

Looks like I can squeak by using the fd2 in 9v and the MXR Chorus out of the 18v tap on the ISO 5.

The pedal I am concerned about most is the AF2 Paul Gilbert Airplane Flanger. I'm trying to avoid using a courtesy outlet so I jut daisy chain the ISO5 off of the PP2+

[JohnClark]

Looks like I can squeak by using the fd2 in 9v and the MXR Chorus out of the 18v tap on the ISO 5.

The pedal I am concerned about most is the AF2 Paul Gilbert Airplane Flanger. I'm trying to avoid using a courtesy outlet so I jut daisy chain the ISO5 off of the PP2+

The Full Drive 2 will accept 9-18V so you can power it a 9V from a Pedal Power 2+ from any output with the corresponding DIP switch set to Normal, of for just a taste of the "Higher Headroom Kool-Aid", you can power it at 12V using any one of outputs 1-4 with the corresponding DIP switch set away from Normal.

The AF2 can be powered from any output on your Pedal Power 2+ with the corresponding DIP switch set to Normal, or any 9V Output on your ISO-5.

Good Luck!

[firebird1999us]

Ok after reassessing some pedals I've swapped a few things around and come up with this scenario - all switches in the normal position:

1 ISO5 9v Ditto Looper X2
2 ISO5 9v Custom Audio MC402
3 ISO5 ***OPEN SPOT***
4 ISO5 9v hp Vox Delaylab
5 ISO5 18v MXR Chorus

1 PP2+ 9v Xotic SP Compressor
2 PP2+ 9v MXR Phase 90
3 PP2+ 9v Boss TR2
4 PP2+ 9v Airplane Flanger
5 PP2+ 9v L5 Boss EQ20 Digitech
6 PP2+ 9v L6 Whammy V
7 PP2+ 9v Custom Audio Wah
8 PP2+ 9v Boss TU2 (daisy chain)

Any issues with that?

[JohnClark]

No problem I see.

Good Luck!